Nowadays, there are so many products of 2 hp single phase goulds sump pump in the market and you are wondering to choose a best one.You have searched for 2 hp single phase goulds sump pump in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings 2 hp single phase goulds sump pump which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
535 reviews analysed
1. Zoeller 98-0001 115-Volt 1/2 Horse Power Model M98 Flow-Mate Automatic Cast Iron Single Phase Submersible Sump/Effluent Pump
Description
Product Description
FLOW-MATE” SUBMERSIBLE PUMP 1/2 HP For sump/dewatering septic tank effluent Thermal overload protected Cast iron Stainless steel screws 2-pole float operated mechanical switch 1-1/2″ NPT discharge Passes 1/2″ solids 115 volt 3420 GPH at 5, 3060 GPH at 10, 2580 GPH at 15 head One year limited warranty Display carton. Make sure the pump electrical supply circuit is equipped with fuses or circuit breakers of proper capacity
From the Manufacturer
Zoeller’s Flow-Mate Model M98 Cast Iron Submersible Sump/Effluent Pump features cast iron motor and pump housing, a cast iron switch case, and a cast iron base. All castings are cast iron class 25-30 with 25000# tensile strength. The M98 also features an engineered plastic vortex impeller. The Flow-Mate has a corrosion resistant powder coated epoxy finish. There are no sheet metal parts that will rust or corrode and no screens that will clog. The permanent slip capacitor motor is oil-filled and hermetically sealed. It features automatic reset thermal overload protection. The pump also includes a watertight neoprene square ring between the motor and the pump housing. The pump’s upper and lower bearings are oil fed cast iron. The Flow-Mate’s maximum temperature for effluent or dewatering is 130 Degree Fahrenheit. The entire unit is pressure tested after assembly. The pumps screws, guard, handle, arm and seal assembly are all made of stainless steel. The Flow-Mate includes a float operated submersible (NEMA 6) 2 pole mechanical switch. It also features a carbon and ceramic shaft seal. The pump’s discharge is 1-1/2-Inch NPT. The major width of the Model M98 is 10-1/8-Inch. The major height is 12-Inch.
2. AMT Pump 5760-95 Submersible Shredder Sewage Pump, Cast Iron, 1 HP, 1 Phase, 115V, Curve A, 2" NPT Female Discharge Port
Feature
- Submersible shredder sewage pump for sewage drainage applications with up to 15% solids
- 1 HP, single-phase, 115 VAC electric motor driver
- Cast iron construction with stainless steel motor housing, carbide-tipped shredder impeller, and silicon carbide lower seal
- Maximum flow rate of 130 gpm
- 2″ female NPT discharge port
Description
The AMT Pump 5760-95 submersible shredder sewage pump is a UL- and CSA-listed centrifugal pump constructed with cast iron, a stainless steel motor housing for resistance to corrosion, a carbide-tipped shredder impeller for durability, and a silicon carbide lower seal for resistance to corrosion, and is suitable for sewage drainage applications with up to 15% solids. It is equipped with double mechanical seals for protection of internal components, and measures 18.5 x 8.9 x 11.4 inches (H x W x D). (H is height, the vertical distance from bottom to top; W is width, the horizontal distance from one narrow side to the other; D is depth, the horizontal distance from the front of the discharge port to the back of the unit.) It is capable of transferring up to 130 gallons of fluid per minute (gpm) with zero total head at temperatures ranging from 40 to 104 degrees F (4 to 40 degrees C), and has a 40′ maximum total head rating. This pump comes equipped with a 1 horsepower (HP), single-phase, 115 VAC motor with automatic restart thermal overload protection, rated for continuous duty at 3450 revolutions per minute (rpm) and fitted with a 18′ three-prong power cord. It ships fully assembled and features a carrying handle and a 2″ female National Pipe Thread Taper (NPT) discharge port for compatibility with most discharge hose assemblies. This pump is suitable for a wide range of sewage drainage applications such as sewage pumping stations, septic tanks, sewage treatment plants, dirty water drainage, flood, and emergency use in residential, commercial, and industrial settings.
Pumps use mechanical action to move liquids, gases, or slurries (solids suspended in a liquid or gas). The mechanical action is categorized as either positive displacement (PD) or kinetic. PD pumps capture and release discrete amounts of flow into a chamber and then force it out. Some examples of PD pumps are fuel and oil pumps in cars, pumps in hydraulic systems, and bicycle pumps. Kinetic pumps move liquids, gases, or slurries by transferring energy from the pump’s movement to the flow. They use an impeller to draw the flow in, add energy to the flow, and move it through a volute (a spiral funnel through which the flow moves), and into the system. Some examples of kinetic pumps include centrifugal (the most common pump in industrial applications), in-line pumps, sump pumps, and suction pumps. Energy sources for all types of pumps include wind power, manual operation, electricity, and gasoline or diesel fuel.
American Machine and Tool (AMT) manufactures centrifugal and diaphragm pumps. The company is headquartered in Royersford, PA.
3. GOULDS Pumps LSP0311 Sump Pump, Manual, Stainless, 1/3 hp, 115V
4. AMT Pump 4020-95 Industrial/Commercial Sump Pump, Cast Iron, 1/2 HP, 1 Phase, 115V, Curve D, 2" NPT Female Discharge Port
Feature
- Upright sump pump for industrial, residential, and commercial drainage applications with up to 3/4″ solids
- 1/2 HP, 115 VAC, 60 Hz single-phase TEFC electric motor
- Cast iron body and impeller with 300 series stainless steel shaft and float, with carbon bearings
- Maximum flow rate of 103 gpm
- 2″ female NPT discharge port
Description
The AMT Pump 4020-95 industrial/commercial sump pump is powered by a 1/2 HP, 115 VAC, 60 Hz, single-phase TEFC electric motor, constructed with a cast iron body and impeller, 300 series stainless steel shaft and float, and carbon bearings, and is suitable for a wide range of clean water drainage applications with up to 3/4″ solids. It is capable of transferring up to 103 gallons of fluid per minute (gpm) with zero total head and has a 20′ total head rating. It is equipped with a float assembly for automatic shutoff, a semi-open clog-resistant impeller, 8′ of 16/3 115 VAC line cord, and a 2″ female National Pipe Thread Taper (NPT) discharge port for compatibility with most discharge hose assemblies. It is 39.9″ tall and requires a sump pit at least 14″ in diameter and 24″ deep for operation. This pump can transfer material ranging from 40 to 200 degrees F (4 to 93 degrees C), and it ships fully assembled except for the float assembly. This pump is suitable for clean drainage applications in residential, commercial, and industrial settings where solids do not exceed 3/4″.
Pumps use mechanical action to move liquids, gases, or slurries (solids suspended in a liquid or gas). The mechanical action is categorized as either positive displacement (PD) or kinetic. PD pumps capture and release discrete amounts of flow into a chamber and then force it out. Some examples of PD pumps are fuel and oil pumps in cars, pumps in hydraulic systems, and bicycle pumps. Kinetic pumps move liquids, gases, or slurries by transferring energy from the pump’s movement to the flow. They use an impeller to draw the flow in, add energy to the flow, and move it through a volute (a spiral funnel through which the flow moves), and into the system. Some examples of kinetic pumps include centrifugal (the most common pump in industrial applications), in-line pumps, sump pumps, and suction pumps. Energy sources for all types of pumps include wind power, manual operation, electricity, and gasoline or diesel fuel.
American Machine and Tool (AMT) manufactures centrifugal and diaphragm pumps. The company is headquartered in Royersford, PA.
What’s in the Box?
- 4020-95 cast iron industrial/commercial sump pump
- Float assembly
5. Zoeller 267-0002 Model N267 Waste-Mate Non-Automatic Cast Iron Single Phase Submersible Sewage/Effluent Pump
Feature
- 1/2 HP submersible sewage pump
- 2″ discharge, passes 2″ spherical solids
- Performance: 115 GPM at 5′ TDH, shut-off: 20.5′ TDH
- Non-automatic model, 15′ cord
- 100% factory tested
- Passes 2-Inch spherical solids
- Pumps 128-Gallon per minute with 5-Foot head
- Shut-off head: 21.5-Feet
- Includes a 15-Foot 3-wire neoprene cord
- Completely submersible.Minimum recommended basin size (small load applications): simplex 18” x 30” (45.7 x 76.2 cm), duplex 30” x 36” (76.2 x 91.4 cm)
Description
Product Description
115-Volt 1/2 Horse Power Model N267 Waste-Mate Non-Automatic Cast Iron Single Phase Submersible Sewage/Effluent Pump. If the Pump operates but delivers little or no water – Check strainer housing, discharge pipe, or if check valve is used vent hole must be clear. Discharge head exceeds pump capacity. Low or incorrect voltage. Incorrect motor rotation. Capacitor defective. Incoming water containing air or causing air to enter pumping chamber
From the Manufacturer
Zoeller’s Model N267 Waste-Mate Cast Iron Submersible Sewage/Effluent Pump features an engineered, non-clogging, plastic vortex impeller with metal inserts. The pump housing and base are made of ASTM Class 25 cast iron. This pump is not effected by materials normally found in drainage and sewage pumps. It features an oil filled, hermetically sealed motor and oil lubricated bearings. The motor features automatic reset thermal overload protection. The Waste-Mate has a corrosion resistant powder coated epoxy finish. The pump also includes a watertight neoprene square ring and gasket. The pumps screws, bolts, handle, guard, arm, and seal assembly are all made of stainless steel. The pump also features a carbon and ceramic shaft seal. It has a 2-Inch female and a 3-Inch NPT male discharge. The N267 is watertight and dust tight.
6. Zoeller M53 Mighty-mate Submersible Sump Pump, 1/3 Hp
Description
Product Description
Zoeller Pump Co. M-53 Mighty Mate clear effluent or dewatering submersible pump. Choice of many plumbers and contractors. 1/3 HP cast iron housing with plastic vortex impeller.
9ft. power cord. Truely a all star pump. Powder coated epoxy CI and SS fastners. Oil filled motor with thermal overload. CSA UL SSPMA
From the Manufacturer
When you have residential or commercial wastewater issues, you can count on Zoeller Pumps to deliver the very best solutions-our commitment to top quality offers you years of service and durability.
7. Hallmark Industries MA0343X-4 Deep Well Submersible Pump, 1/2 hp, 110V, 60 Hz, 25 GPM, 150′ Head, Stainless Steel, 4"
Feature
- Pump, Deep Well Submersible Pump, 1HP, 110V 60HZ, 33 Gpm, Stainless Steel, for 5″ or bigger well, long life
- 2 wire pump with built in control box- DOES NOT require external control box
- Industrial grade heavy duty, good for home usage
- Built in thermal protection
- American company
- Use 115V power to run the pump. 110V is a nominal voltage – covers from 100 V to 130V.
- This pump has a max head of 150feet, which is to pump into an open tank, not a pressure tank. Please read the Pump Selection Guide provided under the product details.
8. SCHRAIBERPUMP 4" Deep Well Submersible Pump 1HP, 230v, NEW EXCLUSIVE AXIAL LOAD DESIGN, 242’head, 105PSI max, 22GPM, 2wire, Thermal Protection, stainless steel, 100% COPPER WINDING includes splice kit
Description
SUBMERSIBLE WIRE SPLICE KIT INCLUDED WITH EVERY PUMP PURCHASE!
IMPORTANT: THIS PUMP DOES NOT REQUIRE A CONTROL BOX!
Our Deep Well Pump is ideal for the supply of fresh water to rural homes, farms, and cabins that have 4 inch and greater diameter drilled wells. It is a durable workhorse that will keep you in flow for years to come. Brand new pump in the box! NOT ‘Manufacturer Refurbished’.
-The pump has a thermally protected motor with a 95°F maximum work temperature to keep from overheating while in use.
-2-wire + ground wire design for easy provision and energy efficiency.
-Stainless steel casing keeps this pump sturdy and functioning for years.
-The well pump submersible is easy to install and extremely versatile.
-Patented impeller design provides high flow up and high head, for better performance and longer life than most other well pumps.
-This pump model features a built in check valve, however this check valve is only used to prevent water from going back in the pump and causing backspin of the impellers, but if you are going to use the pump in a pressure system YOU NEED TO USE AT LEAST ONE EXTERNAL CHECK VALVE IN THE PIPE, the valve in the pump won’t fulfill that function.
-1 year warranty.
NOTICE: Our pumps are checked for physical damage before they’re shipped. As soon as you receive it check for any damage that might have occurred during shipping, and please report it to Amazon if you see any.
NOTICE 2: This pump is designed to be used in clear pure water only, even an small amount of sand diluted in the water will damage it, make sure your well pumps clear water before you install it, this is important because damages caused by sand are not covered by the warranty.
9. GOULDS Pumps GT151TE GT Irrigation Pump, Single Phase, TEFC Motor, 2 hp, 115/230V
10. AMT Pump 5792-95 Submersible Utility Pump, Cast Iron, 1/2 HP, 115V, Curve C, 2" NPT Female Discharge Port
Feature
- Submersible centrifugal pump with automatic float switch for clean water drainage applications
- 1/2 HP, single-phase, 115 VAC electric motor driver
- Cast iron body and impeller with stainless steel, brass, plastic, and plated steel components and a Buna-N seal for resistance to oil and solvents
- Maximum flow rate of 65 gpm
- 2″ female NPT discharge port
Description
The AMT Pump 5792-95 submersible utility pump is a UL- and CSA-listed centrifugal pump constructed with a cast iron body and impeller with stainless steel, brass, plastic, and plated steel components and a Buna-N seal for resistance to oil and solvents, and is suitable for a wide variety of clear water drainage applications. It is equipped with double mechanical seals with carbon and ceramic wear faces for protection of internal components, and measures 16.1 x 7.4 x 10 inches (H x W x D). (H is height, the vertical distance from bottom to top; W is width, the horizontal distance from one narrow side to the other; D is depth, the horizontal distance from the front of the discharge port to the back of the unit.) It is capable of transferring up to 65 gallons of fluid per minute (gpm) with zero total head at temperatures ranging from 40 to 104 degrees F (4 to 40 degrees C), and has a 37′ maximum total head rating. This pump comes equipped with a 1/2 horsepower (HP), single-phase, 115 VAC motor with automatic restart thermal overload protection, rated for continuous duty at 3450 revolutions per minute (rpm) and fitted with a 20′ three-prong Underwriters Laboratories (UL)-approved, Stranded Junior Service Thermoplastic Weather-Resistant Compound (SJTW) power cord. It ships fully assembled and features a carrying handle, a mercury-free float switch, and a 2″ female National Pipe Thread Taper (NPT) discharge port for compatibility with most discharge hose assemblies. This pump is suitable for a wide range of residential, industrial, and commercial applications including sump pits, drainage pits, overflow tanks, basements, dewatering, excavation, grain elevators, construction drainage, cooling towers and other applications requiring clear water removal.
Pumps use mechanical action to move liquids, gases, or slurries (solids suspended in a liquid or gas). The mechanical action is categorized as either positive displacement (PD) or kinetic. PD pumps capture and release discrete amounts of flow into a chamber and then force it out. Some examples of PD pumps are fuel and oil pumps in cars, pumps in hydraulic systems, and bicycle pumps. Kinetic pumps move liquids, gases, or slurries by transferring energy from the pump’s movement to the flow. They use an impeller to draw the flow in, add energy to the flow, and move it through a volute (a spiral funnel through which the flow moves), and into the system. Some examples of kinetic pumps include centrifugal (the most common pump in industrial applications), in-line pumps, sump pumps, and suction pumps. Energy sources for all types of pumps include wind power, manual operation, electricity, and gasoline or diesel fuel.
American Machine and Tool (AMT) manufactures centrifugal and diaphragm pumps. The company is headquartered in Royersford, PA.
Conclusion
By our suggestions above, we hope that you can found 2 Hp Single Phase Goulds Sump Pump for you.Please don’t forget to share your experience by comment in this post. Thank you!
